Symbol-technologies LS 3070 User Manual Page 87
- Page / 214
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
6-24
LS 3070 Product Reference Guide: Programming
Beeper Definitions
Standard Use
Beeper Sequence Indication
1 Beep - short high tone A bar code symbol, or magstripe data was
decoded (if decode beeper is enabled).
2 Beeps - long high tone Mis-match between the selected host and the
interface cable.
4 Beeps - long high tone This signifies either a host interface error or a
format or transmission error in the magnetic
stripe card or in a scanned symbol. In that case,
the data is ignored. This will occur if a unit is not
properly configured. Check option settings.
5 Beeps - long high tone Data conversion error. When Ignore Unknown
Characters is disabled, any attempt to transmit
data not supported by the selected host will
produce these error beeps.
6 Beeps - short low tone RF communication error.
- Product Reference Guide 1
- Contents 3
- Chapter 7. Parameter Menus 5
- Chapter 8. Keyboard Maps 6
- About This Manual 7
- Symbol Support Center 8
- Chapter 1 9
- The LS 3070 Cordless Scanner 9
- The LS 3070 Scanner 10
- Rechargeable Battery Pack 11
- The Base/Charger Unit 12
- Chapter 2 13
- Scanner from Base/Charger 14
- Charging the Battery 15
- Base/Charger Underside 16
- Rotary Switches 16
- Installing a Magstripe Reader 19
- Chapter 3 20
- Scanning with the LS 3070 20
- Hold at an Angle 21
- Scan the Entire Symbol 21
- Scanner? 22
- Scanning Transmission Range 23
- What If 24
- Decode Zones 25
- LS 3070LR Long Range 26
- F) on high quality symbols 27
- LS 3070XLR Extra Long Range 28
- LS 3070HV High Visibility 29
- Chapter 4 Maintenance and 30
- Specifications 30
- Changing Battery Packs 31
- Release 32
- LS 3070 Battery Pack 32
- Charge Status LED Indications 33
- Accessories 34
- Chapter 5 40
- Interface Guide 40
- OCIA and OCR Terminals 41
- RS-232C Single Port 42
- RS-232C Dual Port 42
- IBM 4683/4684/4693/4694 43
- Connecting Keyboard Wedges 44
- IBM 3683/3684 Installation 45
- Printer Ground Strap 48
- Connector 48
- Locking Tab 48
- Figure 5-9. Cable 49
- Figure 5-10. J16 Connector 49
- Figure 5-12. Securing J1 50
- IBM 3653 Installation 51
- Figure 5-13. Removing Panel 52
- NCR 280 Installation 56
- NCR 2151 Installation 57
- NCR 2152 Installation 59
- NCR 2154/2155 Installation 60
- NCR 7052 Installation 60
- Fujitsu 9000 Installation 61
- Interfaces 62
- Host Type Interface P/N 63
- Chapter 6 64
- Programming 64
- Scanning Sequence Examples 65
- Parameter Descriptions 66
- Code 39 Full ASCII 67
- Code 39 Check Digit 69
- ITF-14/EAN-13 Conversion 69
- MSI Plessey Check Digit 69
- Beeper Volume 70
- Beep After Good Decode 70
- UPC/EAN Security Level 70
- UPC-A and -E Preamble 71
- RS-232C Options 74
- No Software Handshaking 76
- ACK/NAK Only 76
- ENQ ONLY 76
- ACK/NAK with ENQ 77
- ASCII Format 78
- Transmit AIM ID Character 79
- Parameter Selections 84
- Beeper Definitions 87
- Parameter Menu Scanning 88
- Code 39 Scan And Store 88
- Code 39 Buffering 89
- Transmit Buffer 90
- Default Table 91
- Table 6-3. Defaults 92
- Chapter 7 96
- Parameter Menus 96
- Set Default Parameter 97
- Host Interface 98
- Single Port RS-232 99
- Dual Port RS-232 99
- IBM PC/XT And Clones 101
- IBM 3653 Keyboard Wedge 101
- IBM PS2-30 and Clones 101
- NCR 2152 (Tel) Keyboard Wedge 104
- NCR 2151 (Tel) Keyboard Wedge 104
- Code Type 112
- ADD D 2 of 5 115
- DELETE D 2 of 5 115
- ADD I 2 of 5 115
- DELETE I 2 of 5 115
- ADD MSI Plessey 116
- DELETE MSI Plessey 116
- ADD CODABAR 116
- DELETE CODABAR 116
- Code Lengths 117
- I 2 OF 5 - ANY LENGTH* 119
- I 2 OF 5 - 1 DISCRETE LENGTH 119
- I 2 OF 5 - 2 DISCRETE LENGTHS 119
- D 2 OF 5 - ANY LENGTH 120
- D 2 OF 5 - 1 DISCRETE LENGTH 120
- D 2 OF 5 - 2 DISCRETE LENGTHS 120
- MSI Plessey - ANY LENGTH 121
- Decode Options 124
- CONVERT UPC-E TO UPC-A 125
- DO NOT CONVERT UPC-E TO UPC-A 125
- TRANSMIT “NO DECODED MESSAGE 127
- DO NOT BUFFER CODE 39 128
- BUFFER CODE 39 128
- VERIFY CODE 39 CHECK DIGIT 128
- BEEP AFTER GOOD DECODE 129
- DO NOT BEEP AFTER GOOD DECODE 129
- UPC/EAN SECURITY LEVEL 3 131
- DECODE REDUNDANCY 1 131
- DECODE REDUNDANCY 3 131
- DECODE REDUNDANCY 2 131
- UPC-A Preamble 132
- UPC-E Preamble 133
- Pause Duration 134
- Prefix/Suffix Values 137
- SCAN SUFFIX (VALUE 1) 138
- SCAN PREFIX (VALUE 2) 138
- MAGSTRIPE PREFIX (VALUE 4) 138
- MAGSTRIPE SUFFIX (VALUE 3) 138
- Data Transmission Formats 141
- <DATA> <SUFFIX> 142
- Magstripe Options 143
- ERASE ALL FORMATS 147
- ERASE LAST ENTERED FORMAT 147
- Laser Control 148
- Baud Rate 151
- Check Parity 154
- Hardware Handshaking 155
- Software Handshaking 156
- Serial Response Timeout 157
- Stop Bit Select 160
- ASCII Data Format 161
- RTS Line State 162
- Intercharacter Delay 163
- Transmit Code ID Character 166
- Transmit AIM Code ID 167
- Ignore Unknown Characters 168
- OCIA Clock Polarity 169
- OCIA Transmit Timeout 170
- NCR 2152 Fast Transmit 173
- AT/XT/PS2 175
- Transmit 176
- National Keyboard Types 177
- U.K. English 178
- Set Transmission Frequency 179
- Reserved For Future Use 185
- ITEM 3 ENABLE 186
- ITEM 4 ENABLE 186
- ITEM 4 DISABLE 186
- ITEM 3 DISABLE 186
- ITEM 5 ENABLE 187
- ITEM 5 DISABLE 187
- ITEM 6 ENABLE 187
- ITEM 6 DISABLE 187
- ITEM 7 ENABLE 188
- ITEM 8 ENABLE 188
- ITEM 8 DISABLE 188
- ITEM 7 DISABLE 188
- APPLICATIONS VALUE 0 TO 255 189
- Chapter 8 193
- Keyboard Maps 193
- Keyboard Identifier Maps 197
- IBM 3179 IBM 3180 IBM 319X 198
- IBM 347X Telex 122 198
- IBM PS2 and Clones 198
- *3001 for IBM 3151 199
- Wyse 60 ANSI Keyboard 200
- Wyse 60 ASCII Keyboard 200
- Wyse 60/85/150/185 201
- IBM 3178 202
- HP 700/9X 202
- IBM 3278 203
- NCR 2151 204
- NCR 2152 27-KEY 204
- NCR 2155 205
- NCR 2157 205
- NCR 2950 206
- NCR 7052 32-KEY 207
- NCR 7052 58-KEY 207
- IBM 3683 116-KEY 210
- IBM 3653 210
- Tell Us What You Think 214
© 2020, manymanuals.com. All rights reserved. | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals